Testing Your Setup by Using Backup Exec. You can back up your data to virtual tapes, archive the tapes. Disabling a Tape Drive in Backup Exec. I do not use backup exec but with all other backup programs that I have used you install the backup software on one computer with it connecting to the tape drive. How to configure Standalone Tape Drive/Auto loader/Library with Backup Exec for Windows Server 1. Make sure the device is detected in the Windows Device Manager as shown in the Figure 1 below. Make sure SCSI ID 0,1, and 6 is not assigned as they are reserved SCSI IDs. To check, go to Device Manager as shown in Figure 2 below. Figure 2 Following is the recommended configuration for SCSI settings. ![]() ![]() SCSI ID recommendation for standalone tape drive, Auto loader/Library. SCSI ID:0 and 1 is basically reserved for hard drives because they are fast devices and hence require lowest priority. SCSI ID:6 The target ID 6 is reserved for automatic configuration of SCSI devices (through plug and play SCSI a.k.a. SCAM) Tape devices, Auto loaders, and Libraries receive the next higher SCSI ID and so on. The reason for higher priority on the SCSI bus is because they are considerably slower devices. They require a much large time slice to accomplish tasks, whereas a hard disk requires a very small time slice because of how fast it is. Typically hard disks are set with the lower SCSI ID# such as 0 and 1. Usually the SCSI IDs may be set on the back of the unit via dials or toggle switches. For more information about setting SCSI ID, please contact your drive manufacturer. The following is an example of what a SCSI map of a Library configured with three SCSI tape devices may look like: SCSI ID:2 - Robotic Arm (Also referred to as the Picker Arm/Changer Arm) SCSI ID:3 - Tape Drive 0 SCSI ID:4 - Tape Drive 1 SCSI ID:5 - Tape Drive 2 NOTE: Backup Exec for Windows Servers, in general requires that the Auto loader/Library's Robotic Arm SCSI ID# precedes the SCSI ID# of the tape drive(s) and then configure the tape devices SCSI IDs in an ascending order as shown above. Once the proper SCSI ID is assigned to the drive, Install the drivers with the help of the information in the Related Documents section of this article 4. After the installation of drivers, go to the Devices tab and check the device presence, Figure 1 shows a Typical Standalone Tape drive and Figure 2 shows a Typical 6 slot Autoloader. Figure1 Figure2 Related Articles. I received this help (which worked) in the Dell support forums: What you need to do is to power on the 110T first and wait for it to go idle. Once the unit is at a ready state then you can boot the server. While the server is going through post you will see it scan the SCSI card and should see the drive. Once the server logs into windows then the drive should be present in device manger. Once the drive is seen by windows then you will need to run the tape install wizard for backup exec as it has a tape drive driver that will work for 2008 R2. Hi Chaplain, The thing is to connect your drive to a card that supports it. Not many RAID controllers will support a tape drive connected to it, and certainly don't support libraries and autoloaders with multiple SCSI IDs. Check the Dell website and look for compatibility between the card you have attached the drive too, and the drive itself. If it isn't listed, you're going to have to purchase a card that does. If it becomes a BE support issue, then you'd need to upgrade to a version of BE that does support that drive. I received this help (which worked) in the Dell support forums: What you need to do is to power on the 110T first and wait for it to go idle. Once the unit is at a ready state then you can boot the server. While the server is going through post you will see it scan the SCSI card and should see the drive. Once the server logs into windows then the drive should be present in device manger. Once the drive is seen by windows then you will need to run the tape install wizard for backup exec as it has a tape drive driver that will work for 2008 R2. Alright So just got that brand new or not so brand new Robotic Library (Autoloader/Changer) and or Tape Drive(s). Still bubble wrap / ship safe fresh, just unpacked and attached to the server and bam. Here comes the brick wall. The storage device is not displaying or perhaps the tape drives or libraries show up offline or worse yet they are not found, recognized or detected at all. What do you do? Well you have a couple of options you can spin once counter clockwise, blink your left eye, wiggle the mouse frantically, right click and see if its working now. Or you can take the suggested approach and follow this informative right down the golden paved road to the promise land of problem resolution.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
November 2018
Categories |